SUPERIOR FLUID SOLUTIONS · BUYER’S GUIDE
Sourcing Fittings for a Data Center Water Cooling System
A purchasing checklist for the instrument and tubing lines, from the bill of materials to the flush schedule.
Buyers planning a data center water cooling system are shopping while the money behind these builds is still rising. According to the Meta earnings call transcript published by Investing.com on 21 October 2026, Meta now expects 2026 capital expenditures, including principal payments on finance leases, of $135 billion to $145 billion, narrowed from $130 billion to $145 billion, and it reported $34.9 billion of capex in the third quarter alone. This guide stays on the buying side: the instrument and tubing lines of the loop, where a wrong tube size or a dirty part costs a commissioning date. If you are new to tube fittings, start there for the product range, then come back for the order checklist.
Why Big Capex Numbers Reach Your Purchasing Desk
Meta’s CFO, Susan Li, said on the same call that “we don’t have anything more specific or quantitative to share until we get to the Q4 call,” and gave no 2027 figure. For a buyer, that means the ceiling has not been set, so do not plan on next year being quieter.
On 22 October 2026, INNIO announced a 620 MW follow-on order, booked in September 2026, from an undisclosed developer and operator of mega-scale US data center campuses. The press release, a manufacturer publication, puts that customer’s total orders at about 1.72 GW and says all 620 MW will be delivered as containerized gas engine units. Neither source mentions fittings. Our reading, and it is only that, is that on-site power adds its own gas and coolant tubing to the same instrument suppliers that cooling projects are already calling.
The Bill of Materials for a Data Center Water Cooling System
The engineer owns the loop design. Your job is to turn the instrument and tubing drawings into lines a supplier can quote without guessing. For the loop architecture itself, see our earlier post on fitting cross-references for data center builds; this guide does not repeat it.
| Line | Confirm before ordering |
|---|---|
| Pressure and temperature taps | Port thread, tube OD, material of any gauge valves |
| Isolation and flow trim | Rating at operating temperature, seat and seal material, needle valves versus quarter-turn |
| Transmitter groups | Port arrangement on manifold valves |
| Protection | Micron rating of inline filters against the coolant spec |
| Tubing runs | Standard, temper, OD, wall, seamless or welded |
| Caps and plugs | Count them; open ends are where dirt gets in |
Lines are a buying checklist, not a design. The engineer of record decides what the loop needs.
What to Confirm Before You Release the Purchase Order
Tube OD and wall. Each fitting size carries a listed wall range, and Superlok North America’s October 2026 tube wall article warns that fittings are “not recommended for tube wall thicknesses outside the ranges shown.” Its pressure rating page bases ratings on the minimum wall and maximum OD allowed under ASTM A269. Put both dimensions on the order, and say inch or metric. If your drawings mix the two, read how to order metric tube fittings from an imperial drawing first.
Material. ASTM A269 covers seamless and welded austenitic stainless steel tubing for general corrosion-resisting and low- or high-temperature service. Superlok® fittings are listed in 316 stainless steel, and the tube wall article says tube must be softer than the fitting, so ask for fully annealed tube in a corrosion-resistant grade such as 316. The ASHRAE TC 9.9 white paper adds two points for buyers: obtain a wetted-materials list from every component supplier, and treat aluminum with care because it can promote galvanic corrosion. Request material test reports at order; our guide to material test reports for fittings explains what to ask for.
End connections. Confirm the port standard on every instrument and every valve before you buy adapters. The ASHRAE paper suggests straight-thread O-ring terminations, SAE or BSPP, where leak risk is critical on the couplings it describes.
Pressure rating. Superlok North America’s tube wall article also notes that a joint is limited by the lower-rated of the tube and the fitting, so rate the weakest part, not the best one. Ask the design team for maximum working pressure, test pressure and operating temperature. ASHRAE advises checking material compatibility at about 50 to 60°C (122 to 140°F) for its W2 through W4 loops, which are warmer than building water.
Cleanliness. This is where purchasing matters most. According to the Open Compute Project’s September 2026 guidelines, a trade-association document for closed-loop propylene glycol systems, filtration should use filters rated at 50 microns or finer, with 25 microns or finer preferred. The same document says stainless steel quick connects should be used, and that flushing with uninhibited water is not preferred because of corrosion risk with certain metals. For the tube runs that carry this coolant, Superlok® supplies fittings with the finest interior surface finish of any tube and pipe fitting on the market.
Planning Lead Time for Cooling Loop Parts
We give no lead-time figures here because none of the sources above publishes one, and ours are confirmed per order at quotation. What you can plan is the order of events. The Open Compute Project says coolant should preferably be installed within 24 hours of flushing, and that systems with only stainless steel, elastomers and plastics can be exposed to air for up to 72 hours. That puts a hard stop behind your delivery date: parts must be on site, inspected and installed before the flush window opens.
Work backwards from there. Quote early, since Meta has not set a 2027 number. Split the list into standard catalog sizes and anything unusual. Keep spare ferrule sets, as in buying and stocking ferrule sets. And keep a fallback ready, as described in what to do with a back-ordered fitting.
Buyer Questions on Water Cooling Orders
What do I send with a quote request?
For each line: tube OD and wall, material and temper, end connections, working and test pressure, temperature, quantity, any material test report requirement, and how clean the parts must arrive.
Does the tube need to match the fitting material?
The tube must be softer than the fitting. Fully annealed 316 stainless steel tube to ASTM A269 is the usual starting point, but the engineer confirms the grade.
Can purchasing decide how the loop is flushed?
No. The Open Compute Project guidance compares cleaning solution, coolant and uninhibited water. Follow the commissioning specification and only make sure the parts and dates support it.
Does this guide give a heat load per rack?
No. We could not source a current figure, so we leave it out. Take it from the project’s engineers.
Bring the tube schedule
Send OD, wall, material and ends for each line, and we will check them against what we list.
SUPERIOR FLUID SOLUTIONS
Instrument fittings and valves, bought by the line item.
Sources
- Investing.com, “Earnings call transcript: Meta beats Q3 2026 estimates as AI push lifts shares,” 21 October 2026. Supports the $135 to $145 billion range, the prior $130 to $145 billion range, Q3 capex of $34.9 billion and the CFO’s comment on 2027. investing.com
- INNIO, “INNIO secures 620 MW data center follow-on order,” 22 October 2026 (manufacturer press release). Supports the order size, September 2026 booking, undisclosed customer and 1.72 GW cumulative total. innio.com
- Open Compute Project, “Guidelines for Using Propylene Glycol-Based Heat Transfer Fluids in Liquid Cooled Racks,” Revision 2.0, dated 15 September 2026. Supports the filter ratings, stainless steel quick connects, flushing comment and the 24 and 72 hour exposure limits. opencompute.org
- ASHRAE Technical Committee 9.9, “Water-Cooled Servers: Common Designs, Components, and Processes,” white paper, 2019. Supports wetted-materials lists, aluminum and galvanic corrosion, straight-thread terminations and the 50 to 60°C compatibility check. ashrae.org
- ASTM International, A269/A269M scope (2013 edition page). Supports the tubing scope and the austenitic stainless steel description. astm.org
- Superlok North America, “Choosing Tube Wall Thickness for Pressure and Bending,” 3 October 2026 (manufacturer publication). Supports wall ranges, tube softer than fitting, annealed tube, the lower-rated-part rule and 316 stainless steel listing. superloknorthamerica.com
- Superlok North America, pressure rating page (manufacturer publication). Supports the minimum wall and maximum OD basis under ASTM A269. superloknorthamerica.com
Technical note: The sources establish the Meta and INNIO figures as announced, the Open Compute Project guidance for closed-loop propylene glycol coolant (facility water is outside its scope), the 2019 ASHRAE white paper, and the manufacturer’s published wall and rating basis. They do not publish lead times, prices, stock levels or a per-rack heat load, and neither Meta nor INNIO addresses fittings, so that link is our own reading. The ASTM page shown is the 2013 edition, so confirm the current revision. Grade and rating are confirmed per order.
Trademark disclaimer: Superlok® is a registered mark of its owner. Meta, INNIO, Investing.com, the Open Compute Project, ASHRAE and ASTM are named only as publishers of the sources cited, and their marks belong to their owners. Cross-references are made by form, fit, and function only.
